NodeMCU — Infrared Remote Control & MQTT

/*  ___   ___  ___  _   _  ___   ___   ____ ___  ____ 
 * / _ \ /___)/ _ \| | | |/ _ \ / _ \ / ___) _ \|    \
 *| |_| |___ | |_| | |_| | |_| | |_| ( (__| |_| | | | |
 * \___/(___/ \___/ \__  |\___/ \___(_)____)___/|_|_|_|
 *                  (____/
 * NodeMCU将收到的红外遥控器的编码发到MQTT Client
 * Tutorial URL
 * CopyRight John Yu
 */
#include <ESP8266WiFi.h>
#include <PubSubClient.h>
#include <IRremoteESP8266.h>

int RECV_PIN = D2; //an IR detector/demodulatord is connected to GPIO pin D2
// Update these with values suitable for your network.
//const char* ssid = "your_ssid";
//const char* password = "your_hotspot_password";
//const char* mqtt_server = "iot.eclipse.org";
//const char* mqtt_server = "broker.mqttdashboard.com";
const char* ssid = "74170287";
const char* password = "24063173";
const char* mqtt_server = "broker.mqttdashboard.com";


WiFiClient espClient;
PubSubClient client(espClient);
IRrecv irrecv(RECV_PIN);
decode_results results;

long lastMsg = 0;
char msg[50];
int value = 0;

void setup_wifi() {
   delay(100);
  // We start by connecting to a WiFi network
    Serial.print("Connecting to ");
    Serial.println(ssid);
    WiFi.begin(ssid, password);
    while (WiFi.status() != WL_CONNECTED)
    {
      delay(500);
      Serial.print(".");
    }
  randomSeed(micros());
  Serial.println("");
  Serial.println("WiFi connected");
  Serial.println("IP address: ");
  Serial.println(WiFi.localIP());
}

void callback(char* topic, byte* payload, unsigned int length)
{
 
} //end callback

void reconnect() {
  // Loop until we're reconnected
  while (!client.connected())
  {
    Serial.print("Attempting MQTT connection...");
    // Create a random client ID
    String clientId = "ESP8266Client-";
    clientId += String(random(0xffff), HEX);
    // Attempt to connect
    //if you MQTT broker has clientID,username and password
    //please change following line to    if (client.connect(clientId,userName,passWord))
    if (client.connect(clientId.c_str()))
    {
      Serial.println("connected");
     //once connected to MQTT broker, subscribe command if any
      client.subscribe("alex9ufo_IR_Command");
    } else {
      Serial.print("failed, rc=");
      Serial.print(client.state());
      Serial.println(" try again in 5 seconds");
      // Wait 5 seconds before retrying
      delay(5000);
    }
  }
} //end reconnect()

void setup() {
  Serial.begin(115200);
  setup_wifi();
  client.setServer(mqtt_server, 1883);
  client.setCallback(callback);
  irrecv.enableIRIn(); // Start the receiver
}

void loop() {
  if (!client.connected()) {
    reconnect();
  }
  client.loop();
  long now = millis();
  //每隔6S发送一次数据
  if (now - lastMsg > 2000) {
     lastMsg = now;
    if (irrecv.decode(&results))
    {
      Serial.println(results.value, HEX);
      irrecv.resume(); // Receive the next value
      String msg="Receive value: ";
       msg= msg+ results.value;
       char message[58];
       msg.toCharArray(message,58);
       Serial.println(message);
       //publish sensor data to MQTT broker
      client.publish("alex9ufo_IR_Data", message);
     }
  }
}