HX711 Load Cell + NODEMCU

/*
 * circuits4you.com
 * 2016 November 25
 * Load Cell HX711 Module Interface with Arduino to measure weight in Kgs
 Arduino
 pin
 2 -> HX711 CLK
 3 -> DOUT
 5V -> VCC
 GND -> GND

 Most any pin on the Arduino Uno will be compatible with DOUT/CLK.
 The HX711 board can be powered from 2.7V to 5V so the Arduino 5V power should be fine.
*/

#include "hx711.h"
#define DOUT 0 // D3 
#define CLK 2  // D4

HX711 scale(DOUT, CLK);

//Change this calibration factor as per your load cell once it is found you many need to vary it in thousands
//float calibration_factor = -96650; //-106600 worked for my 40Kg max scale setup
float calibration_factor = (-382155);   //worked for my 5Kg max scale setup
//=============================================================================================
//                         SETUP
//=============================================================================================
void setup() {
  Serial.begin(115200);
  Serial.println("HX711 Calibration");
  Serial.println("Remove all weight from scale");
  Serial.println("After readings begin, place known weight on scale");
  Serial.println("Press a,s,d,f to increase calibration factor by 10,100,1000,10000 respectively");
  Serial.println("Press z,x,c,v to decrease calibration factor by 10,100,1000,10000 respectively");
  Serial.println("Press t for tare");
  delay(3000);
  scale.set_scale();
  scale.tare(); //Reset the scale to 0

  long zero_factor = scale.read_average(); //Get a baseline reading
  Serial.print("Zero factor: "); //This can be used to remove the need to tare the scale. Useful in permanent scale projects.
  Serial.println(zero_factor);
  Serial.println();
  Serial.println("HX711 Scale Reading .....");
 
}

//=================================================================
//                         LOOP
//=================================================================
void loop() {
  scale.set_scale(calibration_factor); //Adjust to this calibration factor
  if (scale.get_units() > 0.002)
   {
     Serial.println("Reading: ");
     Serial.print(scale.get_units(), 4);
     Serial.print(" kg"); //Change this to kg and re-adjust the calibration factor if you follow SI units like a sane person
     Serial.print(" calibration_factor: ");
     Serial.print(calibration_factor);
   
     Serial.println();
     scale.power_down();
     delay(1000);
     scale.power_up();
   }
   else
   {
     Serial.println("HX711 Scale Reading .....");
     scale.power_down();
     delay(1000);
     scale.power_up();
   }
 
 
  if(Serial.available())
  {
    char temp = Serial.read();
    if(temp == '+' || temp == 'a')
      calibration_factor += 10;
    else if(temp == '-' || temp == 'z')
      calibration_factor -= 10;
    else if(temp == 's' || temp == 'S')
      calibration_factor += 100; 
    else if(temp == 'x'|| temp == 'X')
      calibration_factor -= 100; 
    else if(temp == 'd'|| temp == 'D')
      calibration_factor += 1000; 
    else if(temp == 'c'|| temp == 'C')
      calibration_factor -= 1000;
    else if(temp == 'f'|| temp == 'F')
      calibration_factor += 10000; 
    else if(temp == 'v'|| temp == 'V')
      calibration_factor -= 10000; 
    else if(temp == 't'|| temp == 'T')
      scale.tare();  //Reset the scale to zero
  }
}
//==========================================================