How To Use the ESP8266 and Arduino as a Webserver

by MIGUEL on DECEMBER 30, 2014

in ESP8266

Video Tutorial: How The Code Works

The video below shows you how the ESP8266 works as a webserver with the Arduino using the code below.

Arduino Webserver Code/Sketch For ESP8266

The code handles the ESP8266’s initialization in the setup() function: it resets the module, configures it as an access point, prints out the module’s ip address, configures for multiple connections, configures as a server on port 80.

When there is data available if the string +IPD is in the serial data then the HTTP response is sent to the browser or device requesting it.

#include <SoftwareSerial.h>
 
#define DEBUG true
 
SoftwareSerial esp8266(2,3); // make RX Arduino line is pin 2, make TX Arduino line is pin 3.
                             // This means that you need to connect the TX line from the esp to the Arduino's pin 2
                             // and the RX line from the esp to the Arduino's pin 3
void setup()
{
  Serial.begin(9600);
  esp8266.begin(9600); // your esp's baud rate might be different
  
 
  
  sendData("AT+RST\r\n",2000,DEBUG); // reset module
  sendData("AT+CWMODE=2\r\n",1000,DEBUG); // configure as access point
  sendData("AT+CIFSR\r\n",1000,DEBUG); // get ip address
  sendData("AT+CIPMUX=1\r\n",1000,DEBUG); // configure for multiple connections
  sendData("AT+CIPSERVER=1,80\r\n",1000,DEBUG); // turn on server on port 80
}
 
void loop()
{
  if(esp8266.available()) // check if the esp is sending a message 
  {
    /*
    while(esp8266.available())
    {
      // The esp has data so display its output to the serial window 
      char c = esp8266.read(); // read the next character.
      Serial.write(c);
    } */
    
    if(esp8266.find("+IPD,"))
    {
     delay(1000);
 
     int connectionId = esp8266.read()-48; // subtract 48 because the read() function returns 
                                           // the ASCII decimal value and 0 (the first decimal number) starts at 48
     
     String webpage = "<h1>Hello</h1>&lth2>World!</h2><button>LED1</button>";
 
     String cipSend = "AT+CIPSEND=";
     cipSend += connectionId;
     cipSend += ",";
     cipSend +=webpage.length();
     cipSend +="\r\n";
     
     sendData(cipsend,1000,DEBUG);
     sendData(webpage,1000,DEBUG);
     
     webpage="<button>LED2</button>";
     
     cipSend = "AT+CIPSEND=";
     cipSend += connectionId;
     cipSend += ",";
     cipSend +=webpage.length();
     cipSend +="\r\n";
     
     sendData(cipsend,1000,DEBUG);
     sendData(webpage,1000,DEBUG);
 
     String closeCommand = "AT+CIPCLOSE="; 
     closeCommand+=connectionId; // append connection id
     closeCommand+="\r\n";
     
     sendData(closeCommand,3000,DEBUG);
    }
  }
}
 
 
String sendData(String command, const int timeout, boolean debug)
{
    String response = "";
    
    esp8266.print(command); // send the read character to the esp8266
    
    long int time = millis();
    
    while( (time+timeout) > millis())
    {
      while(esp8266.available())
      {
        
        // The esp has data so display its output to the serial window 
        char c = esp8266.read(); // read the next character.
        response+=c;
      }  
    }
    
    if(debug)
    {
      Serial.print(response);
    }
    
    return response;
}
 

Related posts:

• ESP8266 Arduino LED Control (Control The Digital Pins Via WiFi, Send Data From Webpage to Arduino)

• ESP8266 Android Application to Control Arduino Digital Pins and Toggle LEDs

• ESP8266 Arduino Code and Schematic to Send AT Commands and Print Output

• Make a Phone Call With Voice Using Your ESP8266 and Arduino With Twilio’s API

• How To Send Text Messages From The ESP8266 and Twilio Using NodeMcu

PREVIOUS POST: ESP8266 Arduino Code and Schematic to Send AT Commands and Print Output

NEXT POST: ESP8266 Arduino LED Control (Control The Digital Pins Via WiFi, Send Data From Webpage to Arduino)